Stone Powder Coated on Architectural Foam and Fabrication Services

Stonecoat is a coating material for EPS architectural foam shapes.
It has exceptional adhesive capabilities and can be applied to a variety of surface types.

SURFACE PREPARATION
All surfaces must be free of debris, dirt and dust, grease, oils, curing agents, and cleaning solutions.

Glossy or painted surfaces must be sanded and cleaned to ensure a proper bond.

MIXING INSTRUCTIONS
1. Each 50-pound bag will generally require 1 to 1-1/2 gallons of clean water depending on the application.
2. It is recommended that a mechanical mixing device be used.
3. Start with 3/4 to 1 gallon clean water.
4. Add bag of foam coat and mix until material is thoroughly saturated.
5. Add the balance of the required water and mix for 5 minutes; be sure that the product is thoroughly mixed.
6. Let the blended material sit for 5 minutes, then remix to break the set before any application.

SURFACE COATING
Stonecoat should be applied with a coating of 3/16?to 1/4?thick to the foam shapes, and can be applied
either by a machine or by hand.

MACHINE EXTRUSION APPLICATION
1. Follow procedure for normal mixing instructions, but after foam coat is mixed, let it sit for 10 minutes then remix to break set.
2. You must obtain a creamy consistency for proper machine applied application.
3. When coatings over 3/16?are desired, 2 coats may be required allowing first coat to dry before second coat is applied.

CURING
All coated shapes should be moist cured and allowed to dry is a shaded non-windy area.

Allow a minimum cure period of 24 hours before applying an exterior finish over the coated EPS shape.

CLEAN UP
Immediately clean all tools and mixing equipment with water after use.

COVERAGE
One 50-pound bag will cover approximately 40?0 sq. feet.

SAFETY
Contains Portland cement. Wear rubber gloves and eye protection.
Avoid eye contact or prolonged contact with skin.
If eye contact occurs, flush with water for 15 minutes. Consult physician immediately. This product contains free silica. Do not breathe dust; wear NIOSH approved respirator.

Material Safety Data Sheet (M S D S)

MANUFACTURER Arcufoamstone
19709 Scriber Lake Rd., Suite H, Lynnwood, WA 98036 USA
Emergency phone: (0118) 2154-40161                                                                                                   
SECTION I: PRODUCT IDENTIFICATION StoneCoat

SECTION II: HAZARDOUS INGREDIENTS                                   
Component: Portland Cement (CAS 65997-15-1)
OSHA PEL: 10 mg/m3
ACGIH TLV: 15 mg/m3
Component: Calcium Hydroxide (Lime) (CAS 1305-62-0)
OSHA PEL: 2 mg/m3
ACGIH TLV: 5 mg/m3
Component: Silica sand (CAS 01-4808-60-7)
OSHA PEL: 5 mg/m3 (respirable) 0.3 mg/m3 (total dust)
ACGIH TLV: 0.05 mg/m3 (respirable dust)

SECTION III: PHYSICAL DATA                                                    
Appearance and Odor: Gray or white sandy powder material, slight odor.
Boiling Point: N/A Melting Point: N/A Vapor Pressure: N/A
Vapor Density: N/A Specifi c Gravity: N/A Solubility: Slight
Evaporation Rate: N/A Percent Volatility: N/A

SECTION IV: FIRE AND EXPLOSION HAZARD DATA                
Flash Point: Noncombustible Flammable Limits: N/A
Extinguishing Media: N/A Special Fire Fighting Procedures: N/A
Personal Protection: Protect against airborne dust. Use an approved dust mask

SECTION V: REACTIVITY DATA
Stability: Stable.
Incompatibility: Hydrated lime is incompatible with acids, ammonia salts and some
organic compounds.
Hazardous Decomposition: Will not occur.
Hazardous Polymerization: Will not occur.

SECTION VI: HEALTH HAZARD DATA                                           
Primary Routes of Exposure: Inhalation, Skin and Eye Contact.
Inhalation: Inhalation of dust can cause headache, nausea, irritation and/or infl ammation of nose, throat or lungs.
Eye Contact: Direct contact with eyes can cause eye irritation and/or alkali burns.
Skin Contact: Prolonged or repeated skin contact with wet material can cause skin
irritation and/or alkali burns.
Inhalation: Move subject to fresh air.
Eye Contact: Flush eyes with running water for at least 15 minutes. Consult a physician if irritation persists.
Skin Contact: Wash affected area thoroughly with soap and water. Consult a physician if irritation persists.
Ingestion: If swallowed, give at least 2 glasses of water to drink, consult a physician.
Never give anything by mouth to an unconscious person.
Carcinogenicity: IARC: SiO2, NTP: SiO2, OSHA: Not Regulated

SECTION VII: SAFE HANDLING AND USE                                
Procedures: Handle as a nuisance dust. Use respiratory protection if dust becomes airborne.
Waste Disposal: Dispose of in accordance with applicable Federal, State and Local
regulations. Keep spills and runoff out of municipal sewers and open bodies of water.

SECTION VIII: SPECIAL PROTECTION DATA                         
Respiratory Protection: Eliminate esposure to dust, use OSHA/NIOSH approved respirators for silica dust.
Eye Protection: Use goggles approved against nuisance dust.
Hand Protection: Rubber gloves are recommended to provide protection against wet material.
Other Protective equipment: Local ventilation. Eyewash station.

SECTION IX: SPECIAL PRECAUTIONS                                
US DOT Hazard Class: Not Regulated.
NTP: Health 0 Flammability 0 Reactivity 0
HMIS: Health * Flammabilty 0 Reactivity 0 Protective Equipment E
(Health rating applies only to acute effects as defi ned by the National Paint and Coatings Association.)
NA= NOT APPLICABLE C= CENTIGRADE F= FAHRENHEIT DATE: 4/11/06
Arcufoamstone, as an OEM distribution company, blending company notified us of processed material in the State of
California, is required by Proposition 65 to warn that one or more of the components contained in this product could contain chemicals known to the State of California to cause cancer, birth defects or other reproductive harm. The State of California (Proposition 65) requires this warning in the absence of defi nitive testing to prove that the defi ned risks do not exist. We believe this product complies with all other applicable state and federal laws and regulations governing manufacture, distribution and intended use.
This information is furnished without warranty, representation, inducement or license of any kind. The information presented here is believed to be accurate to the best of Arcufoamstone’s knowledge or is obtained from sources believed to be accurate. Arcufoamstone does not assume any legal responsibility for its use or reliance upon same.